These modules are made available by Evergreen, one of the world's largest manufacturers. Made in USA! Identical Power specifications as A grade modules, complete factory light tower test is available. These modules have the same 0% to +5% power output tolerances as "A" modules. These modules have slight cosmetic blemishes. Sun modules are non-UL, Tuv or CE listed. Unlike most other brands which have power specifications within +/- 10%, these modules have power specifications within 0% to +5% ! There is no better output power allowance in the industry.
 |
Made in the U.S.A. |
| Model | SUN ES-A-205-fa3 |
| Power (W) | 205 Watts |
| Open Circuit Voltage (V) | 22.70 Voc |
| Short Circuit Current (A) | 11.93 Isc |
| Maximum Power Voltage (V) | 18.20 Vmp |
| Maximum Power Current (A) | 11.27 Imp |
| Dimensions (in)(LxWxD) | 65" x 37 1/2" x 1 3/8" |
| Weight (lb) | 41 lb |
| Connector | MC-4 |
Charge Controller
Outback Power FLEXmax 60 MPPT Solar Charge Controller
The FLEXmax
family of charge controllers is the latest
innovation in Maximum Power Point Tracking (MPPT)
charge controllers from OutBack Power
Systems. The innovative FLEXmax MPPT
software algorithm is both continuous and
active, increasing your photovoltaic array
power yield up to 30% compared to non-MPPT
controllers. Thanks to active cooling and
intelligent thermal management cooling, both
FLEXmax charge controllers can operate at
their full maximum current rating, 60 Amps
or 80 Amps respectively, in ambient
temperatures as high as 104°F (40°C).
Included in all of the FLEXmax Charge
Controllers are the revolutionary features
first developed by OutBack Power, including
support for a wide range of nominal battery
voltages and the ability to step-down a
higher voltage solar array to recharge a
lower voltage battery bank. A built-in,
backlit 80 character display shows the
current status and logged system performance
data for the last 128 days at the touch of a
button. The integrated OutBack network
communications allows FLEXmax series Charge
Controllers to be remotely programmed and
monitored via a MATE system display and
provides unrivaled complete system
integration.
Note: This replaces the Outback Power MX-60.
Inverter
Magnum Energy MS2012 Pure Sine Wave Inverter + Charger, 2000 Watts for 12v battery bank.
Please contact us if you need to substitute a 24v or 48v inverter
Free Shipping 48 statesThe MS Series Inverter/Charger is a pure sine wave inverter designed specifically for the most demanding mobile and off grid applications. The MS Series is powerful, easy-to-use, and best of all, cost effective. Install the MS Series in four easy steps: simply connect the inverter's output to your distribution circuits or electrical panel, connect your shore power cable (AC) to the inverter's easy-to-reach terminal block, connect the batteries, and switch on the power.
The MS-AE Series Inverter/Charger
from Magnum Energy is a pure sine wave inverter designed
specifically for the most demanding renewable energy
applications. The unique design of the MS-AE Series can
provide 120 and 240 volts AC output in one unit,
eliminating the need to stack two units together to get
240 volts. Available in 4000 (24 volts) and 4400 (48
volts) watt models, the MS-AE Series inverters are
powerful, easy-to-use and ETL listed to the stringent
requirements of UL 1741 and CSA C22.2 No. 107.1-01 for
Renewable Energy installations.
Besides off-grid systems, the MS2012 inverter is very
popular for RV's and marine use. Pure sine wave and a
built in 100 amp battery charger makes it ideal for new
installations, or replacement or upgrade for older
modified sine wave inverters. In RV's this will replace
both the inverter and the converter. The built in
battery charger will run from standard AC nearly all
generators of 2000 watts or more.
Pure sinewave power for your stereo, plasma screens, and
other sensitive electronics. The MS Series is designed
for both mobile and off-grid applications. Competitively
priced, the MS-Series is available in 2000, 2800 and
4000 watt models.
Install the MS Series in four easy steps: simply connect
the inverter's output to your AC distribution circuits
or electrical panel, connect your shore power cable (AC)
to the inverter's easy-to-reach terminal block, connect
the batteries, and switch on the power.
The MS Series is ETL listed to the stringent
requirements of UL/cUL 458 for mobile use and UL 1741
for off grid installations.
Magnum MS2012 2000 Watt Pure Sine Wave inverter w/charger, 100 amp 12v charger For a 12v battery bank
Optional MC4 connector cable is recommended, so you can cut it in half and strip back each end to connect your panel to your charge controller.
 |
30
Foot MC4 Solarline 2,
Extender Cable
Male/Female
30 foot MC4 extender
cable M/F
|
We recommend www.Win-SolarLLC.com for custom made solar interconnect networks, cables and accessories. In addition to what we offer here on our site, you can also buy custom network circuits for your pv array direct. This will save you time and money on your install. Also FYI SunWindProducts does not make any money from any direct purchases from Win-Solar.
Your Choice - Design a network for your solar field.
2. Select your choice of materials and draw a simple line chart to match your field requirements. ~Be sure to identify the length of each leg of the network and indicate whether male or female connectors are required.
~Complete this form for each field network you need.
~Refer to the printable example below.
3. Email to info@Win-SolarLLC.com or fax to 678-261-8895 (be sure to include your contact information).
If you have your own drawings you may email, fax or mail them to Win-Solar LLC.
Please make sure all drawings and prints are clear and legible.
Sample of parallel network strings
Youtube video with general explanation of how solar wiring works
